Відео

No crank no start No

Good evening, saw your video, great, Just wondering how the new dust seal gets installed? on the front Axle assembly, or is it pushed in? When you install the axle shaft and that new seal gets installed at the same time, please let me know, thx😊

If you have oil will you still hear the Injector ?

This is pro level editing. Feels like a quality show. Well done

Hey buddy you do awesome work!. And this is by far the best how to video i have ever seen. Man it's great every detail. And you take the time to walk through every little hint to help with every step from start to finish. Thank you so much

What benefits does this have over stock?

Worked great and looks great in my 06

Just ordered 2 more yesterday 😂

Where can I purchase one with a sensor what's the cost also

This problem is intermittent which differentiates it from slop in the steering box etc which is consistent year after year. If you only operate in 2wd can both shafts be removed completely to solve this steering wander problem?

Good stuff brother!

why didn't you put the battery pan in last, to have better access to install cooler and hose install?? just a thought

Can you show some close ups of where you welded in the S550? And are you going to have another video of boxing the frame in?

Love the progress, little by little brother 👍😁

Press tool no longer included. Bought a pair of new TTX Ball Joints that are press in exactly as shown here. Also the preload was way off on the ball joint from India. The Indiana Joint also didn't even come with a zerk fitting snap ring or even a new Castle nut. Very disappointing

Well spoken

I have a oil leak that is situated in front of the oil pan between the brace for the oil pan in the middle of it any ideas ?

Great video!! Thanks for educating the industry!

How much coolant to replace?

Love the channel. 2017 f-150 cold air intake cat back exhaust 6" lift on35"swatted to buy a tuner . Wife passed away suddenly and now I can't afford one. Thanks again love the channel

Can you have a battery tender hooked up during install?

Anymore videos on laptop

We had same vibration. Removed the drive shaft and it’s notchy and not very smooth for sure, but when we drove the vehicle without it to confirm this was the problem, while it’s better it now has a shake at 110-120kph and it’s not as violent. We’ve done lower control arms, sway bar link, tie rod ends. Now need to get alignment done. Also balanced wheels. Any suggestions?

@hueyfab nice little kit

My 97 F350 is doing the wandering thing. I was going to mess with the steering box, but now I will check the U joints first. Thanks

Wrong! You welded the new metal right over the rusted, now how are you going to get rust converter behind it. Rust will keep growing like a fungus. 👎

Wow. World class instructional video.

I followed your video, replacing oil sensor on my 2013...you saved me so much money..THANK YOU...YOUR AN AWESOME MECHANIC

We have 2010 ford edge that vibrates when sharp turning g especially left turn. Sound and vibration is mostly coming from the left rear end. Could it still be the drive shalf with the cv joints?

It's just not so productive.How come they didn't put 2 bolts?And you have a nut on top and tighten it down.How stupid are the engineers

Love this video. I just did this yesterday. I used a large impact chisel (Hilti) and ended up pulling a lot of the spot welds out, meaning a lot of holes. I'll fix (most of) them, but a sharp chisel or the grinder (as in the video) would be better. The bad part is I saw the read cab mounts --- all 6 have to be replaced and that's a worse job!

Are you getting the viking coilovers that ATP offers as well?

The tablet and the interface seem to be Launch product.

I sorry does this apply to a Ford e150 van ,as I do have that 10 to 2 sloppy steering problem.

Why halfway through the video do you stop mentioning the socket sizes and such it's very useful information.

Thank you. Great video.

Excellent work

will this work on a 2006 kia sorento?

my manifold bolt broke off a little below the surface on my 6.0 . I think i got steel or cast iron heads. Is that possible on a 6.0 or are they all aluminum. I'm worried about welding the bolt to the head.

So do you delete the engine bay fuel filter???

Thank you so much. I just finished repairing my 2012 Sorento oil sensor leak. Being able to walk through this in advance and know what sizes of socket I needed was worth a lot to me.

Just seeing this vid. Man, I appreciate this. Love all the deets. Good shizz my guy 🤘🏼

I have a 99 f250 that will pull to left, pull to the right , kinda feels like it will dart to the left or right sometimes and sometimes when I turn it kinda has a roll over feeling in the steering wheel. I replaced the drag link because I found it was bad. The issue is better but it still isn’t right. Any ideas what it could be?

Which one would you choose 6.4 Ram, or 6.0 f250..?

I have a 04 f350 6.0 is the oil cooler relocate worth the money?

I just received my board from Amazon today. With your video I'll be removing the other one and installing this one. Wish me luck I was hoping I did not have to have any kind of reconfiguration with the computer. Thanks for the video!

No foolish music. Thank god

How can I get a printed version of instructions. I did not receive one when o bought my kit

Thank you very much. Very helpful 👌.

Rotors ❤❤